Simple Desk With Drawer Plans

Do yous demand DIY desk plans?  Whether yous're working from dwelling or need a desk-bound for online learning, you've come up to correct identify. My girl had been begging for her ain desk always since she saw the Desk with Hidden Wireless Charging.  I wanted to make her a DIY desk-bound with centre-communicable details like tapered legs, cove molding, and a chamfered hardwood top.  I'll show y'all how I did information technology all, forth with some tips to make information technology easier.  And be sure to check out my DIY Desk Plans if you desire to build your own DIY Desk-bound!

Before we get started, make sure to follow me on YouTube, Facebook and Instagram to continue upwardly with all my latest builds!

Hither is what you'll need for the project:

Affiliate links are used on this folio.  See my disclosure page for info on chapter programs.

How To Build a DIY Desk With Drawers

1. Cut the Desk Legs
2. Create Desk-bound Side Panels
3. Attach Desk-bound Side Panels and Legs
4. Create Desk Elevation
5. Make Desk Drawers
6. Install Desk Drawers

1. Cut the DIY Desk Legs

First I started past cutting the legs for the DIY desk to size and using my stop block on my miter saw stand which is great for repeatable cuts.

Using layout marks to keep the legs in social club, I marked the bottom of the legs for a small-scale taper.  The taper will be on the within two faces of each leg.

To cut the tapers I used a elementary jig.  The edge represents the cut line, but keep an eye on which taper yous cut first.  If I cut this side first I'd remove the layout line for the 2nd cut. Always think about the 2d cutting before making the start.

After clamping down the DIY desk leg and running it through I flipped it over and took a second pass for the other confront.

Finally I finished upwardly the leg tapers on the other legs using my layout lines for guidance.

Back at the workbench I used the reference lines to reorder the legs.  You can run across how the tapers volition look when assembled.

2. Create the Side Panels for the Desk

When because how to build a desk yous can use a floating or solid side console.  I decided to go for a solid side with a faux floating panel wait.  The sides of the desk have a plywood panel held between a pair of 2×2 legs.  First I cut the plywood to size and and so added pocket holes to the edges of the panels with my K4 jig.

Then I moved on to assembling the side panels.  I laid out 2 legs making sure the tapers were oriented correctly for the outside facing down.  Next I used two small-scale ¾" scraps to prop upwardly the console even with the inside edge of the legs. This will give a affluent surface for the drawer slides subsequently.

The panel is fastened to the legs using a modest bead of glue and 1-¼" pocket screws.  Clamping the parts tightly helps proceed them from moving every bit the screws go in.

The outside of the side has a faux frame and console look.  I cut a top and bottom trim slice from a 1×2 to fit between the legs.  And so I attached them with glue and brad nails.

I wanted a nice finished look for the desk with drawers  so I used cove molding effectually the inside of the panel.  To fit the molding I cut a miter on i terminate of the trim and then took information technology to the panel and marked it for the second cutting.  I continue this approach all the mode effectually the panel.

Next I secured the molding in place with glue and pin nails and so came back and filled all the boom holes with wood putty.

I needed to hide the pocket holes on inside left panel to prep for painting subsequently, so I glued small sections of woods dowels into the holes.  Then I tapped the dowels in with a hammer and so after the glue has a chance to setup I cut them flush with a pull saw.

iii. Attach DIY Desk Side Panels and Legs

Next I cut the full sized plywood dorsum to length on my tabular array saw so drilled pocket holes on the edges.  I clamped the dorsum in identify and attached it with pocket screws.

The front stretcher of the DIY desk is cutting to the same length and is also given pocket holes for assembly.  I attached the front stretcher with pocket screws.

I cut the parts for the box that holds the drawers from my sheet of plywood.  To clean upwardly the edges of the plywood box I cut some solid wood edge banding from a slice of 1×4.  I cut the strips long and used glue to adhere the border banding.  It'due south held in place to dry with painter's tape.  Afterward the glue dries I cut the long strips flush with my pull saw.

Next I cutting the panels to proper length on the table saw.  The vertical panel needed a notch for the front stretcher.  I used a 1×2 to layout the notch and marked for the cut. This cut can be fabricated with a bandsaw like I used or with a jigsaw or hand saw.

The cut face up is rough afterwards and can be cleaned up with a chisel.

I assembled the two panels together outset, then fastened them to the desk side and back.  I attached the panels to the side first then to the meridian stretcher.

This establishes the squareness of the front of the box then I worked my way effectually the rest of the box.

A desk with drawers obviously needs a place for them to go then I added couple of dividers to establish the openings for the drawers.  These are cutting to size to fit the openings and fastened with pocket screws.

Adjacent I started painting using a semi-gloss white enamel and applying it with a HVLP sprayer.

iv. Create the DIY Desk Top

I started with rough lumber and took information technology through the milling process to become dimensioned boards for my top glue upwards.  But if y'all don't take these machines don't fret, you lot can take woods dimensioned to your specs or buy information technology already cut to size at a variety of lumber dealers both brick and mortar and online.

With all the boards dimensioned to size but left a little long I glue up the summit.  I used a expert amount of wood glue to get a solid connexion then clamped that top within an inch of its life.  The more than clamps, the better.

Side by side I took the summit for the DIY desk-bound out of the clamps.  I knocked downward the glue joints and got rid of whatever excess glue so started finish sanding.  Drawing pencil lines on your boards is a slap-up fashion to know when y'all're ready for the next grit.  Once the lines are gone yous know y'all're skilful.

Then I put a chamfer on the underside of the front and sides of the top for the DIY desk.  I used my compact router and fabricated multiple passes to get to the size chamfer I wanted.

After a final sanding I practical a coat of oil based polyurethane.  I ended upward doing 3 coats in total to withstand the wrath of a half dozen year old girl.  And how bout that crimson, it's looks astonishing.

v. Brand Desk Drawers

A desk with drawers add so much versatility, then now let's build the three drawers.  I take a whole mail and video on How to Make Drawers in 6 Easy Steps and so for more information check that out.  Only these  new corner clamps from Kreg actually work swell to align the drawer.

I made the boxes and attached the bottom just like I show in the post referenced above.  And so I apply veneered edge banding to the tops of the drawers to give them a piddling cleaner wait.  Each drawer will also get an inset false drawer forepart.  I cut the fronts from a one×4.

half dozen. Install the DIY Desk Drawers

The full extension drawer slides demand to be set back ¾" since the drawers are inset with a false front.  I used a piece of 1×four to position the slides and a spacer to agree them off lesser.  Each slide is pre-drilled and attaches with screws to the sides.

Before installing the drawers I used a biscuit joiner to cutting slots into the sides, back and front stretcher.  I'chiliad using z-clips to adhere the peak to the desk.

The clips fit in the slots and get screwed to the summit.

To install the lesser drawer onto the slides I used a piece of ¼" plywood to raise it off the drawer bottom.  Then I pulled the drawer and slides out and attached information technology to the box.

For the upper drawer and the narrow drawer I measured where I wanted the slides to hit on the drawer then drew a line across the side of the drawer.

I predrilled and attached the slides on the line making sure they were affluent with the front.

To mount the faux fronts on the drawers I drilled two holes in the front of each drawer a few inches from the side.

So I drilled the holes for the drawer hardware on the drawer fronts. I positioned the drawer fronts using my favorite playing bill of fare spacing method and put screws through the drawer pull holes into the box.

This holds the drawer perfectly and you can secure it from the inside through the holes drilled before.

 Now remove the screws from the front, drill through the box and install your drawer pulls.

This desk has just enough details to prepare information technology autonomously and my daughter is going to savour it for a long time to come up.

Cheque out my other Furniture Projects for more than builds!

Kreg Tool provided me with production and/or budgetary compensation every bit a sponsor of this build.  All opinions are my own and are not filtered by the sponsor.

doverphourromposs.blogspot.com

Source: https://fixthisbuildthat.com/diy-desk-with-drawers-plans/

Share this post